Standards catalogue

ISO/TC 138/SC 2

Plastics pipes and fittings for water supplies

  • Filter:
  •  
  •  
  •  
  •  
Standard and/or project under the direct responsibility of ISO/TC 138/SC 2 Secretariat Stage ICS
ISO 264:1976 [Withdrawn]
Unplasticized polyvinyl chloride (PVC) fittings with plain sockets for pipes under pressure -- Laying lengths -- Metric series
95.99
ISO 264:1976/Add 1:1982 [Withdrawn]
Diameters 200 mm and 225 mm
95.99
ISO 727:1985 [Withdrawn]
Fittings of unplasticized polyvinyl chloride (PVC-U), chlorinated polyvinyl chloride (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure -- Dimensions of sockets -- Metric series
95.99
ISO 727-1:2002
Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure -- Part 1: Metric series
90.93
ISO 727-2:2002 [Withdrawn]
Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure -- Part 2: Inch-based series
95.99
ISO 727-2:2005
Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure -- Part 2: Inch-based series
90.93
ISO 1452-1:2009
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure -- Unplasticized poly(vinyl chloride) (PVC-U) -- Part 1: General
90.93
ISO 1452-2:2009
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure -- Unplasticized poly(vinyl chloride) (PVC-U) -- Part 2: Pipes
90.93
ISO 1452-3:2009
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure -- Unplasticized poly(vinyl chloride) (PVC-U) -- Part 3: Fittings
90.93
ISO 1452-4:2009
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure -- Unplasticized poly(vinyl chloride) (PVC-U) -- Part 4: Valves
90.93
ISO 1452-5:2009
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure -- Unplasticized poly(vinyl chloride) (PVC-U) -- Part 5: Fitness for purpose of the system
90.93
ISO 2045:1988 [Withdrawn]
Single sockets for unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly (vinyl chloride) (PVC-C) pressure pipes with elastic sealing ring type joints -- Minimum depths of engagement
95.99
ISO 2048:1990 [Withdrawn]
Double-socket fittings for unplasticized poly(vinyl chloride) (PVC-U) pressure pipes with elastic sealing ring type joints -- Minimum depths of engagement
95.99
ISO 2536:1974 [Withdrawn]
Unplasticized polyvinyl chloride (PVC) pressure pipes and fittings, metric series -- Dimensions of flanges
95.99
ISO 3458:1976 [Withdrawn]
Assembled joints between fittings and polyethylene (PE) pressure pipes -- Test of leakproofness under internal pressure
95.99
ISO 3459:1976 [Withdrawn]
Polyethylene (PE) pressure pipes -- Joints assembled with mechanical fittings -- Internal under-pressure test method and requirement
95.99
ISO 3460:1975 [Withdrawn]
Unplasticized polyvinyl chloride (PVC) pressures pipes -- Metric series -- Dimensions of adapter for backing flange
95.99
ISO 3501:1976 [Withdrawn]
Assembled joints between fittings and polyethylene (PE) pressure pipes -- Test of resistance to pull out
95.99
ISO 3503:1976 [Withdrawn]
Assembled joints between fittings and polyethylene (PE) pressure pipes -- Test of leakproofness under internal pressure when subjected to bending
95.99
ISO 3603:1977
Fittings for unplasticized polyvinyl chloride (PVC) pressure pipes with elastic sealing ring type joints -- Pressure test for leakproofness
90.93
ISO 3604:1976 [Withdrawn]
Fittings for unplasticized polyvinyl chloride (PVC) pressure pipes with elastic sealing ring type joints -- Pressure test for leakproofness under conditions of external hydraulic pressure
95.99
ISO 3663:1976 [Withdrawn]
Polyethylene (PE) pressure pipes and fittings, metric series -- Dimensions of flanges
95.99
ISO 4132:1979
Unplasticized polyvinyl chloride (PVC) and metal adaptor fittings for pipes under pressure -- Laying lengths and size of threads -- Metric series
90.93
ISO/TR 4191:1989 [Withdrawn]
Unplasticized polyvinyl chloride (PVC-U) pipes for water supply -- Recommended practice for laying
95.99
ISO/TR 4191:2014
Plastics piping systems for water supply -- Unplasticized poly(vinyl chloride)(PVC-U) and oriented PVC-U (PVC-O) -- Guidance for installation
60.60
ISO 4422:1990 [Withdrawn]
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply -- Specifications
95.99
95.99
ISO 4422-1:1996 [Withdrawn]
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply -- Specifications -- Part 1: General
95.99
ISO 4422-2:1996 [Withdrawn]
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply -- Specifications -- Part 2: Pipes (with or without integral sockets)
95.99
ISO 4422-3:1996 [Withdrawn]
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply -- Specifications -- Part 3: Fittings and joints
95.99
ISO 4422-4:1997 [Withdrawn]
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply -- Specifications -- Part 4: Valves and ancillary equipment
95.99
ISO 4422-5:1997 [Withdrawn]
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply -- Specifications -- Part 5: Fitness for purpose of the system
95.99
ISO 4427:1996 [Withdrawn]
Polyethylene (PE) pipes for water supply -- Specifications
95.99
ISO 4427-1:2007
Plastics piping systems -- Polyethylene (PE) pipes and fittings for water supply -- Part 1: General
90.92
ISO 4427-1:2007/Amd 1:2015
Melt mass-flow rate (MFR) for PE 80 and PE 100
60.60
60.60
ISO/NP 4427-1 [Under development]
Plastics piping systems -- Polyethylene (PE) pipes and fittings for water supply -- Part 1: General
10.99
ISO 4427-2:2007
Plastics piping systems -- Polyethylene (PE) pipes and fittings for water supply -- Part 2: Pipes
90.92
60.60
ISO/NP 4427-2 [Under development]
Plastics piping systems -- Polyethylene (PE) pipes and fittings for water supply -- Part 2: Pipes
10.99
ISO 4427-3:2007
Plastics piping systems -- Polyethylene (PE) pipes and fittings for water supply -- Part 3: Fittings
90.92
ISO/NP 4427-3 [Under development]
Plastics piping systems -- Polyethylene (PE) pipes and fittings for water supply -- Part 3: Fittings
10.99
ISO 4427-5:2007
Plastics piping systems -- Polyethylene (PE) pipes and fittings for water supply -- Part 5: Fitness for purpose of the system
90.92
ISO/NP 4427-5 [Under development]
Plastics piping systems -- Polyethylene (PE) pipes and fittings for water supply -- Part 5: Fitness for purpose of the system
10.99
ISO 4434:1977 [Withdrawn]
Unplasticized polyvinyl chloride (PVC) adaptor fittings for pipes under pressure -- Laying length and size of threads -- Metric series
95.99
ISO 6455:1983 [Withdrawn]
Unplasticized polyvinyl chloride (PVC) fittings with elastic sealing ring type joints for pipes under pressure -- Dimensions of laying lengths -- Metric series
95.99
ISO 7279:1984 [Withdrawn]
Polypropylene (PP) fittings for pipes under pressure -- Sockets for fusion using heated tools -- Metric series -- Dimensions of sockets
95.99
ISO 8779:1992 [Withdrawn]
Polyethylene (PE) pipes for irrigation laterals -- Specifications
95.99
ISO 8779:2001 [Withdrawn]
Polyethylene (PE) pipes for irrigation laterals -- Specifications
95.99
ISO 8779:2010
Plastics piping systems -- Polyethylene (PE) pipes for irrigation -- Specifications
90.93
60.60
ISO/DIS 8779 [Under development]
Plastics piping systems -- Polyethylene (PE) pipes for irrigation -- Specifications
40.93
ISO 8796:1989 [Withdrawn]
Polyethylene (PE) 25 pipes for irrigation laterals -- Susceptibility to environmental stress-cracking induced by insert-type fittings -- Test method and specification
95.99
ISO 8796:2004
Polyethylene PE 32 and PE 40 pipes for irrigation laterals -- Susceptibility to environmental stress cracking induced by insert-type fittings -- Test method and requirements
90.93
ISO 9623:1997
PE/metal and PP/metal adaptor fittings for pipes for fluids under pressure -- Design lengths and size of threads -- Metric series
90.93
ISO 9624:1997
Thermoplastics pipes for fluids under pressure -- Mating dimensions of flange adapters and loose backing flanges
90.92
ISO/CD 9624 [Under development]
Thermoplastics pipes for fluids under pressure -- Mating dimensions of flange adapters and loose backing flanges
30.60
ISO 9625:1993 [Withdrawn]
Mechanical joint fittings for use with polyethylene pressure pipes for irrigation purposes
95.99
ISO/TR 10501:1993
Thermoplastics pipes for the transport of liquids under pressure -- Calculation of head losses
90.93
ISO 10508:1995 [Withdrawn]
Thermoplastics pipes and fittings for hot and cold water systems
95.99
ISO 10508:2006
Plastics piping systems for hot and cold water installations -- Guidance for classification and design
90.93
ISO 10508:2006/DAmd 1 [Under development]
40.00
ISO 13783:1997
Plastics piping systems -- Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints -- Test method for leaktightness and strength while subjected to bending and internal pressure
90.93
ISO 13844:2000 [Withdrawn]
Plastics piping systems -- Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes -- Test method for leaktightness under negative pressure
95.99
ISO 13845:2000 [Withdrawn]
Plastics piping systems -- Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes -- Test method for leaktightness under internal pressure and with angular deflection
95.99
ISO 13846:2000
Plastics piping systems -- End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping -- Test method for long-term leaktightness under internal water pressure
90.93
ISO 14236:2000 [Withdrawn]
Plastics pipes and fittings -- Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems
95.99
ISO 15874-1:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polypropylene (PP) -- Part 1: General
95.99
95.99
ISO 15874-1:2013
Plastics piping systems for hot and cold water installations -- Polypropylene (PP) -- Part 1: General
90.93
ISO 15874-2:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polypropylene (PP) -- Part 2: Pipes
95.99
95.99
ISO 15874-2:2013
Plastics piping systems for hot and cold water installations -- Polypropylene (PP) -- Part 2: Pipes
90.93
ISO 15874-2:2013/DAmd 1 [Under development]
40.60
ISO 15874-3:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polypropylene (PP) -- Part 3: Fittings
95.99
ISO 15874-3:2013
Plastics piping systems for hot and cold water installations -- Polypropylene (PP) -- Part 3: Fittings
90.93
ISO 15874-3:2013/DAmd 1 [Under development]
40.60
ISO 15874-5:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polypropylene (PP) -- Part 5: Fitness for purpose of the system
95.99
ISO 15874-5:2013
Plastics piping systems for hot and cold water installations -- Polypropylene (PP) -- Part 5: Fitness for purpose of the system
90.93
ISO 15874-5:2013/DAmd 1 [Under development]
40.60
ISO/NP TS 15874-7 [Under development]
Plastics piping systems for hot and cold water installations -- Polypropylene (PP) -- Part 7: Guidance for the assessment of conformity
10.99
ISO/TS 15874-7:2003
Plastics piping systems for hot and cold water installations -- Polypropylene (PP) -- Part 7: Guidance for the assessment of conformity
90.92
ISO 15875-1:2003
Plastics piping systems for hot and cold water installations -- Crosslinked polyethylene (PE-X) -- Part 1: General
90.93
60.60
ISO 15875-2:2003
Plastics piping systems for hot and cold water installations -- Crosslinked polyethylene (PE-X) -- Part 2: Pipes
90.93
60.60
ISO 15875-3:2003
Plastics piping systems for hot and cold water installations -- Crosslinked polyethylene (PE-X) -- Part 3: Fittings
90.93
ISO 15875-5:2003
Plastics piping systems for hot and cold water installations -- Crosslinked polyethylene (PE-X) -- Part 5: Fitness for purpose of the system
90.93
60.60
ISO/NP TS 15875-7 [Under development]
Plastics piping systems for hot and cold water installations -- Crosslinked polyethylene (PE-X) -- Part 7: Guidance for the assessment of conformity
10.99
ISO/TS 15875-7:2003
Plastics piping systems for hot and cold water installations -- Crosslinked polyethylene (PE-X) -- Part 7: Guidance for the assessment of conformity
90.92
ISO 15876-1:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polybutylene (PB) -- Part 1: General
95.99
95.99
ISO 15876-1:2017
Plastics piping systems for hot and cold water installations -- Polybutene (PB) -- Part 1: General
60.60
ISO 15876-2:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polybutylene (PB) -- Part 2: Pipes
95.99
95.99
ISO 15876-2:2017
Plastics piping systems for hot and cold water installations -- Polybutene (PB) -- Part 2: Pipes
60.60
ISO 15876-3:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polybutylene (PB) -- Part 3: Fittings
95.99
ISO 15876-3:2017
Plastics piping systems for hot and cold water installations -- Polybutene (PB) -- Part 3: Fittings
60.60
ISO 15876-5:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polybutylene (PB) -- Part 5: Fitness for purpose of the system
95.99
ISO 15876-5:2017
Plastics piping systems for hot and cold water installations -- Polybutene (PB) -- Part 5: Fitness for purpose of the system
60.60
ISO/NP TS 15876-7 [Under development]
Plastics piping systems for hot and cold water installations -- Polybutylene (PB) -- Part 7: Guidance for the assessment of conformity
10.99
ISO/TS 15876-7:2003
Plastics piping systems for hot and cold water installations -- Polybutylene (PB) -- Part 7: Guidance for the assessment of conformity
90.92
ISO 15877-1:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 1: General
95.99
ISO 15877-1:2009
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 1: General
90.93
60.60
ISO 15877-2:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 2: Pipes
95.99
ISO 15877-2:2009
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 2: Pipes
90.93
60.60
ISO 15877-3:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 3: Fittings
95.99
ISO 15877-3:2009
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 3: Fittings
90.93
60.60
ISO 15877-5:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 5: Fitness for purpose of the system
95.99
ISO 15877-5:2009
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 5: Fitness for purpose of the system
90.93
60.60
ISO/NP TS 15877-7 [Under development]
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 7: Guidance for the assessment of conformity
10.99
ISO/TS 15877-7:2003 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 7: Guidance for the assessment of conformity
95.99
ISO/TS 15877-7:2009
Plastics piping systems for hot and cold water installations -- Chlorinated poly(vinyl chloride) (PVC-C) -- Part 7: Guidance for the assessment of conformity
90.92
ISO 16422:2006 [Withdrawn]
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure -- Specifications
95.99
ISO 16422:2014
Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure -- Specifications
60.60
ISO 21003-1:2008
Multilayer piping systems for hot and cold water installations inside buildings -- Part 1: General
90.93
ISO 21003-2:2008
Multilayer piping systems for hot and cold water installations inside buildings -- Part 2: Pipes
90.93
60.60
ISO 21003-3:2008
Multilayer piping systems for hot and cold water installations inside buildings -- Part 3: Fittings
90.93
ISO 21003-5:2008
Multilayer piping systems for hot and cold water installations inside buildings -- Part 5: Fitness for purpose of the system
90.93
ISO/NP TS 21003-7 [Under development]
Multilayer piping systems for hot and cold water installations inside buildings -- Part 7: Guidance for the assessment of conformity
10.99
ISO/TS 21003-7:2008
Multilayer piping systems for hot and cold water installations inside buildings -- Part 7: Guidance for the assessment of conformity
90.92
60.60
ISO 21004:2006
Plastics piping systems -- Multilayer pipes and their joints, based on thermoplastics, for water supply
90.93
ISO 22391-1:2007 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 1: General
95.99
ISO 22391-1:2009
Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 1: General
90.93
ISO 22391-2:2007 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 2: Pipes
95.99
ISO 22391-2:2009
Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 2: Pipes
90.93
ISO 22391-3:2007 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 3: Fittings
95.99
ISO 22391-3:2009
Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 3: Fittings
90.93
ISO 22391-5:2007 [Withdrawn]
Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 5: Fitness for purpose of the system
95.99
ISO 22391-5:2009
Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 5: Fitness for purpose of the system
90.93
ISO/CD TS 22391-7 [Under development]
Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 7: Guidance for the assessment of conformity
30.00
ISO/TS 22391-7:2011
Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 7: Guidance for the assessment of conformity
90.92
ISO/TR 27165:2012
Thermoplastics piping systems - Guidance for definitions of wall constructions for pipes
90.93

No matching records found