• Фильтр:

  •  
  •  
  •  
  •  
Стандарт и/или проект находящийся в компетенции ISO/TC 213 Секретариата Этап ICS
ISO 1:1975
Standard reference temperature for industrial length measurements
95.99
ISO 1:2002
Geometrical Product Specifications (GPS) — Standard reference temperature for geometrical product specification and verification
95.99
ISO 1:2016
Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties
60.60
ISO 286-1:1988
ISO system of limits and fits — Part 1: Bases of tolerances, deviations and fits
95.99
ISO 286-1:2010
Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits
90.93
ISO 286-1:2010/Cor 1:2013
Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits — Technical Corrigendum 1
60.60
ISO 286-2:1988
ISO system of limits and fits — Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts
95.99
ISO 286-2:1988/Cor 1:2006
ISO system of limits and fits — Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts — Technical Corrigendum 1
95.99
ISO 286-2:2010
Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
90.93
ISO 286-2:2010/Cor 1:2013
Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts — Technical Corrigendum 1
60.60
ISO/R 286:1962
ISO system of limits and fits — Part I : General, tolerances and deviations
95.99
ISO 370:1975
Toleranced dimensions — Conversion from inches into millimetres and vice versa
95.99
ISO 406:1987
Technical drawings — Tolerancing of linear and angular dimensions
95.99
ISO 463:2006
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges
90.20
ISO 463:2006/Cor 1:2007
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 1
60.60
ISO 463:2006/Cor 2:2009
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 2
60.60
ISO/R 463:1965
Dial gauges reading in 0.01 mm, 0.001 in and 0.0001 in
95.99
ISO 468:1982
Surface roughness — Parameters, their values and general rules for specifying requirements
95.99
ISO 1101:1983
Technical drawings — Geometrical tolerancing — Tolerancing of form, orientation, location and run-out — Generalities, definitions, symbols, indications on drawings
95.99
ISO 1101:2004
Geometrical Product Specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
95.99
ISO 1101:2012
Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
95.99
ISO 1101:2012/Cor 1:2013
Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out — Technical Corrigendum 1
95.99
ISO 1101:2017
Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
60.60
ISO 1119:1975
Series of conical tapers and taper angles
95.99
ISO 1119:1998
Geometrical Product Specifications (GPS) — Series of conical tapers and taper angles
95.99
ISO 1119:2011
Geometrical product specifications (GPS) — Series of conical tapers and taper angles
90.93
ISO 1302:2002
Geometrical Product Specifications (GPS) — Indication of surface texture in technical product documentation
90.92
ISO 1660:1987
Technical drawings — Dimensioning and tolerancing of profiles
95.99
ISO 1660:2017
Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing
60.60
ISO 1829:1975
Selection of tolerance zones for general purposes
95.99
ISO 1878:1983
Classification of instruments and devices for measurement and evaluation of the geometrical parameters of surface finish
95.99
ISO 1879:1981
Instruments for the measurement of surface roughness by the profile method — Vocabulary
95.99
ISO 1880:1979
Instruments for the measurement of surface roughness by the profile method — Contact (stylus) instruments of progressive profile transformation — Profile recording instruments
95.99
ISO 1938-1:2015
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size
60.60
ISO 1938-2:2017
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Reference disk gauges
60.60
ISO/R 1938:1971
ISO system of limits and fits — Part II : Inspection of plain workpieces
95.99
ISO 1947:1973
System of cone tolerances for conical workpieces from C = 1:3 to 1:500 and lengths from 6 to 630 mm
95.99
ISO 2538-1:2014
Geometrical product specifications (GPS) — Wedges — Part 1: Series of angles and slopes
90.20
ISO 2538-2:2014
Geometrical product specifications (GPS) — Wedges — Part 2: Dimensioning and tolerancing
90.20
ISO 2538:1974
Limits and fits — Series of angles and slopes on wedges and prisms
95.99
ISO 2538:1998
Geometrical Product Specifications (GPS) — Series of angles and slopes on prisms
95.99
ISO 2632-1:1975
Roughness comparison specimens — Part 1: Turned, ground, bored, milled, shaped and planed
95.99
ISO 2632-1:1985
Roughness comparison specimens — Part 1: Turned, ground, bored, milled, shaped and planed
95.99
ISO 2632-2:1977
Roughness comparison specimens — Part 2: Spark-eroded, shot blasted and grit blasted, and polished
95.99
ISO 2632-2:1985
Roughness comparison specimens — Part 2: Spark-eroded, shot-blasted and grit-blasted, and polished
95.99
ISO 2632-3:1979
Roughness comparison specimens — Part 3: Cast surfaces
95.99
ISO 2692:1988
Technical drawings — Geometrical tolerancing — Maximum material principle
95.99
ISO 2692:1988/Amd 1:1992
Technical drawings — Geometrical tolerancing — Maximum material principle — Amendment 1: Least material requirement
95.99
ISO 2692:2006
Geometrical product specifications (GPS) — Geometrical tolerancing — Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
95.99
ISO 2692:2014
Geometrical product specifications (GPS) — Geometrical tolerancing — Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
90.92
ISO/DIS 2692
Geometrical product specifications (GPS) — Geometrical tolerancing — Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
40.99
ISO 2768-1:1989
General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
90.93
ISO 2768-2:1989
General tolerances — Part 2: Geometrical tolerances for features without individual tolerance indications
90.92
ISO 2768:1973
Permissible machining variations in dimensions without tolerance indication
95.99
ISO 3040:1990
Technical drawings — Dimensioning and tolerancing — Cones
95.99
ISO 3040:2009
Geometrical product specifications (GPS) — Dimensioning and tolerancing — Cones
95.99
ISO 3040:2016
Geometrical product specifications (GPS) — Dimensioning and tolerancing — Cones
60.60
ISO 3274:1975
Instruments for the measurement of surface roughness by the profile method — Contact (stylus) instruments of consecutive profile transformation — Contact profile meters, system M
95.99
ISO 3274:1996
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments
90.93
ISO 3274:1996/Cor 1:1998
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments — Technical Corrigendum 1
60.60
ISO 3599:1976
Vernier callipers reading to 0,1 and 0,05 mm
95.99
ISO 3611:1978
Micrometer callipers for external measurement
95.99
ISO 3611:2010
Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
90.92
ISO/CD 3611
Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
30.99
ISO 3650:1978
Gauge blocks
95.99
ISO 3650:1998
Geometrical Product Specifications (GPS) — Length standards — Gauge blocks
90.20
ISO 3650:1998/Cor 1:2008
Geometrical Product Specifications (GPS) — Length standards — Gauge blocks — Technical Corrigendum 1
60.60
ISO 3670:1979
Blanks for plug gauges and handles (taper lock and trilock) and ring gauges — Design and general dimensions
95.99
ISO 4287-1:1984
Surface roughness — Terminology — Part 1: Surface and its parameters
95.99
ISO 4287-2:1984
Surface roughness — Terminology — Part 2: Measurement of surface roughness parameters
95.99
ISO 4287:1997
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
90.92
ISO 4287:1997/Amd 1:2009
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters — Amendment 1: Peak count number
60.60
ISO 4287:1997/Cor 1:1998
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters — Technical Corrigendum 1
60.60
ISO 4287:1997/Cor 2:2005
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters — Technical Corrigendum 2
60.60
ISO 4288:1985
Rules and procedures for the measurement of surface roughness using stylus instruments
95.99
ISO 4288:1996
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Rules and procedures for the assessment of surface texture
90.93
ISO 4288:1996/Cor 1:1998
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Rules and procedures for the assessment of surface texture — Technical Corrigendum 1
60.60
ISO 4291:1985
Methods for the assessement of departure from roundness — Measurement of variations in radius
90.93
ISO 4292:1985
Methods for the assessment of departure from roundness — Measurement by two- and three-point methods
95.99
ISO 5166:1982
System of cone fits for cones from C = 1 : 3 to 1 : 500, lengths from 6 to 630 mm and diameters up to 500 mm
95.99
ISO 5436-1:2000
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 1: Material measures
90.93
ISO 5436-2:2001
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards
95.99
ISO 5436-2:2001/Cor 1:2006
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards — Technical Corrigendum 1
95.99
ISO 5436-2:2001/Cor 2:2008
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards — Technical Corrigendum 2
95.99
ISO 5436-2:2012
Geometrical product specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards
90.93
ISO 5436:1985
Calibration specimens — Stylus instruments — Types, calibration and use of specimens
95.99
ISO 5458:1998
Geometrical Product Specifications (GPS) — Geometrical tolerancing — Positional tolerancing
95.99
ISO 5458:2018
Geometrical product specifications (GPS) — Geometrical tolerancing — Pattern and combined geometrical specification
60.60
ISO 5459:1981
Technical drawings — Geometrical tolerancing — Datums and datum-systems for geometrical tolerances
95.99
ISO 5459:2011
Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
90.93
ISO/TR 5460:1985
Technical drawings — Geometrical tolerancing — Tolerancing of form, orientation, location and run-out — Verification principles and methods — Guidelines
95.99
ISO 6318:1985
Measurement of roundness — Terms, definitions and parameters of roundness
95.99
ISO 6906:1984
Vernier callipers reading to 0,02 mm
95.99
ISO 7863:1984
Height setting micrometers and riser blocks
90.93
ISO 8015:1985
Technical drawings — Fundamental tolerancing principle
95.99
ISO 8015:2011
Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules
90.93
ISO 8062-1:2007
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 1: Vocabulary
90.93
ISO 8062-3:2007
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings
90.92
ISO 8062-3:2007/Cor 1:2009
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings — Technical Corrigendum 1
60.60
ISO 8062-4:2017
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: General tolerances for castings using profile tolerancing in a general datum system
90.92
ISO 8062:1984
Castings — System of dimensional tolerances
95.99
ISO 8062:1994
Castings — System of dimensional tolerances and machining allowances
95.99
ISO/CD 8062-4
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: General tolerances for castings using profile tolerancing in a general datum system
30.99
ISO/DIS 8062-3
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings
40.99
ISO/TS 8062-2:2013
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2: Rules
90.20
ISO 8512-1:1990
Surface plates — Part 1: Cast iron
90.93
ISO 8512-2:1990
Surface plates — Part 2: Granite
90.93
ISO 8785:1998
Geometrical Product Specification (GPS) — Surface imperfections — Terms, definitions and parameters
90.20
ISO 9493:2010
Geometrical product specifications (GPS) — Dimensional measuring equipment: Dial test indicators (lever type) — Design and metrological characteristics
90.93
ISO 10135:2007
Geometrical product specifications (GPS) — Drawing indications for moulded parts in technical product documentation (TPD)
90.93
ISO 10360-10:2016
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 10: Laser trackers for measuring point-to-point distances
90.92
ISO 10360-12:2016
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 12: Articulated arm coordinate measurement machines (CMM)
60.60
ISO 10360-1:2000
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 1: Vocabulary
90.93
ISO 10360-1:2000/Cor 1:2002
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 1: Vocabulary — Technical Corrigendum 1
60.60
ISO 10360-2:1994
Coordinate metrology — Part 2: Performance assessment of coordinate measuring machines
95.99
ISO 10360-2:2001
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 2: CMMs used for measuring size
95.99
ISO 10360-2:2009
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 2: CMMs used for measuring linear dimensions
90.93
ISO 10360-3:2000
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 3: CMMs with the axis of a rotary table as the fourth axis
90.93
ISO 10360-4:2000
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode
90.92
ISO 10360-4:2000/Cor 1:2002
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode — Technical Corrigendum 1
60.60
ISO 10360-5:2000
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 5: CMMs using multiple-stylus probing systems
95.99
ISO 10360-5:2010
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 5: CMMs using single and multiple stylus contacting probing systems
90.92
ISO 10360-6:2001
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 6: Estimation of errors in computing Gaussian associated features
90.93
ISO 10360-6:2001/Cor 1:2007
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 6: Estimation of errors in computing Gaussian associated features — Technical Corrigendum 1
60.60
ISO 10360-7:2011
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 7: CMMs equipped with imaging probing systems
90.93
ISO 10360-8:2013
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 8: CMMs with optical distance sensors
90.93
ISO 10360-9:2013
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 9: CMMs with multiple probing systems
90.93
ISO/CD 10360-11
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 11: CMMs using the principle of computed tomography (CT)
30.60
ISO/CD 10360-13
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 13: Optical 3D CMS
30.60
ISO/DIS 10360-10
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 10: Laser trackers
40.99
ISO/FDIS 10360-5
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 5: CMMs using single and multiple stylus contacting probing systems using discrete point and/or scanning measuring mode
50.00
ISO 10578:1992
Technical drawings — Tolerancing of orientation and location — Projected tolerance zone
95.99
ISO 10579:1993
Technical drawings — Dimensioning and tolerancing — Non-rigid parts
95.99
ISO 10579:2010
Geometrical product specifications (GPS) — Dimensioning and tolerancing — Non-rigid parts
90.93
ISO 10579:2010/Cor 1:2011
Geometrical product specifications (GPS) — Dimensioning and tolerancing — Non-rigid parts — Technical Corrigendum 1
60.60
ISO 11562:1996
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Metrological characteristics of phase correct filters
95.99
ISO 11562:1996/Cor 1:1998
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Metrological characteristics of phase correct filters — Technical Corrigendum 1
95.99
ISO 12085:1996
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Motif parameters
90.92
ISO 12085:1996/Cor 1:1998
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Motif parameters — Technical Corrigendum 1
60.60
ISO 12179:2000
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments
90.92
ISO 12179:2000/Cor 1:2003
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments — Technical Corrigendum 1
60.60
ISO/CD 12179
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments
30.99
ISO 12180-1:2011
Geometrical product specifications (GPS) — Cylindricity — Part 1: Vocabulary and parameters of cylindrical form
90.93
ISO 12180-2:2011
Geometrical product specifications (GPS) — Cylindricity — Part 2: Specification operators
90.93
ISO/TS 12180-1:2003
Geometrical Product Specifications (GPS) — Cylindricity — Part 1: Vocabulary and parameters of cylindrical form
95.99
ISO/TS 12180-2:2003
Geometrical Product Specifications (GPS) — Cylindricity — Part 2: Specification operators
95.99
ISO/TS 12180-2:2003/Cor 1:2010
Geometrical Product Specifications (GPS) — Cylindricity — Part 2: Specification operators — Technical Corrigendum 1
95.99
ISO 12181-1:2011
Geometrical product specifications (GPS) — Roundness — Part 1: Vocabulary and parameters of roundness
90.93
ISO 12181-2:2011
Geometrical product specifications (GPS) — Roundness — Part 2: Specification operators
90.93
ISO/TS 12181-1:2003
Geometrical Product Specifications (GPS) — Roundness — Part 1: Vocabulary and parameters of roundness
95.99
ISO/TS 12181-2:2003
Geometrical Product Specifications (GPS) — Roundness — Part 2: Specification operators
95.99
ISO/TS 12181-2:2003/Cor 1:2010
Geometrical Product Specifications (GPS) — Roundness — Part 2: Specification operators — Technical Corrigendum 1
95.99
ISO 12780-1:2011
Geometrical product specifications (GPS) — Straightness — Part 1: Vocabulary and parameters of straightness
90.93
ISO 12780-2:2011
Geometrical product specifications (GPS) — Straightness — Part 2: Specification operators
90.93
ISO/TS 12780-1:2003
Geometrical Product Specifications (GPS) — Straightness — Part 1: Vocabulary and parameters of straightness
95.99
ISO/TS 12780-2:2003
Geometrical Product Specifications (GPS) — Straightness — Part 2: Specification operators
95.99
ISO/TS 12780-2:2003/Cor 1:2010
Geometrical Product Specifications (GPS) — Straightness — Part 2: Specification operators — Technical Corrigendum 1
95.99
ISO 12781-1:2011
Geometrical product specifications (GPS) — Flatness — Part 1: Vocabulary and parameters of flatness
90.93
ISO 12781-2:2011
Geometrical product specifications (GPS) — Flatness — Part 2: Specification operators
90.93
ISO/TS 12781-1:2003
Geometrical Product Specifications (GPS) — Flatness — Part 1: Vocabulary and parameters of flatness
95.99
ISO/TS 12781-2:2003
Geometrical Product Specifications (GPS) — Flatness — Part 2: Specification operators
95.99
ISO/TS 12781-2:2003/Cor 1:2010
Geometrical Product Specifications (GPS) — Flatness — Part 2: Specification operators — Technical Corrigendum 1
95.99
ISO/PAS 12868:2009
Geometrical product specification (GPS) — Coordinate measuring machines (CMM): Testing the performance of CMMs using single-stylus contacting probing systems
95.99
ISO 13102:2012
Geometrical product specifications (GPS) — Dimensional measuring equipment: Electronic digital-indicator gauge — Design and metrological characteristics
90.93
ISO 13225:2012
Geometrical product specifications (GPS) — Dimensional measuring equipment; Height gauges — Design and metrological characteristics
90.93
ISO 13385-1:2011
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Callipers; Design and metrological characteristics
95.99
ISO 13385-1:2019
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Design and metrological characteristics of callipers
60.60
ISO 13385-2:2011
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Calliper depth gauges; Design and metrological characteristics
90.92
ISO/FDIS 13385-2
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Calliper depth gauges; Design and metrological characteristics
50.00
ISO 13565-1:1996
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 1: Filtering and general measurement conditions
90.93
ISO 13565-1:1996/Cor 1:1998
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 1: Filtering and general measurement conditions — Technical Corrigendum 1
60.60
ISO 13565-2:1996
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 2: Height characterization using the linear material ratio curve
90.92
ISO 13565-2:1996/Cor 1:1998
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 2: Height characterization using the linear material ratio curve — Technical Corrigendum 1
60.60
ISO 13565-3:1998
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 3: Height characterization using the material probability curve
90.92
ISO 14253-1:1998
Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for proving conformance or non-conformance with specifications
95.99
ISO 14253-1:2013
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for proving conformity or nonconformity with specifications
95.99
ISO 14253-1:2017
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
60.60
ISO 14253-2:2011
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
90.93
ISO 14253-2:2011/Cor 1:2013
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification — Technical Corrigendum 1
60.60
ISO 14253-3:2011
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 3: Guidelines for achieving agreements on measurement uncertainty statements
90.93
ISO 14253-5:2015
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 5: Uncertainty in verification testing of indicating measuring instruments
60.60
ISO/TR 14253-6:2012
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 6: Generalized decision rules for the acceptance and rejection of instruments and workpieces
60.60
ISO/TS 14253-2:1999
Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
95.99
ISO/TS 14253-2:1999/Cor 1:2007
Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification — Technical Corrigendum 1
95.99
ISO/TS 14253-3:2002
Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 3: Guidelines for achieving agreements on measurement uncertainty statements
95.99
ISO/TS 14253-4:2010
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 4: Background on functional limits and specification limits in decision rules
90.93
ISO 14405-1:2010
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
95.99
ISO 14405-1:2016
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
60.60
ISO 14405-2:2011
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 2: Dimensions other than linear sizes
95.99
ISO 14405-2:2018
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 2: Dimensions other than linear or angular sizes
60.60
ISO 14405-3:2016
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 3: Angular sizes
60.60
ISO 14406:2010
Geometrical product specifications (GPS) — Extraction
90.93
ISO 14638:2015
Geometrical product specifications (GPS) — Matrix model
60.60
ISO/TR 14638:1995
Geometrical product specification (GPS) — Masterplan
95.99
ISO 14660-1:1999
Geometrical Product Specifications (GPS) — Geometrical features — Part 1: General terms and definitions
95.99
ISO 14660-2:1999
Geometrical Product Specifications (GPS) — Geometrical features — Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature
95.99
ISO 14978:2006
Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment
95.99
ISO 14978:2006/Cor 1:2008
Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment — Technical Corrigendum 1
95.99
ISO 14978:2018
Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment
60.60
ISO 15530-3:2011
Geometrical product specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 3: Use of calibrated workpieces or measurement standards
90.93
ISO/TS 15530-1:2013
Geometrical product specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 1: Overview and metrological characteristics
90.20
ISO/TS 15530-3:2004
Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 3: Use of calibrated workpieces or standards
95.99
ISO/TS 15530-4:2008
Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 4: Evaluating task-specific measurement uncertainty using simulation
90.93
ISO/TR 16015:2003
Geometrical product specifications (GPS) — Systematic errors and contributions to measurement uncertainty of length measurement due to thermal influences
90.93
ISO/TR 16570:2004
Geometrical Product Specifications (GPS) — Linear and angular dimensioning and tolerancing: +/- limit specifications — Step dimensions, distances, angular sizes and radii
95.99
ISO 16610-1:2015
Geometrical product specifications (GPS) — Filtration — Part 1: Overview and basic concepts
60.60
ISO 16610-20:2015
Geometrical product specifications (GPS) — Filtration — Part 20: Linear profile filters: Basic concepts
60.60
ISO 16610-21:2011
Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters: Gaussian filters
90.93
ISO 16610-22:2015
Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters: Spline filters
60.60
ISO 16610-28:2016
Geometrical product specifications (GPS) — Filtration — Part 28: Profile filters: End effects
60.60
ISO 16610-29:2015
Geometrical product specifications (GPS) — Filtration — Part 29: Linear profile filters: Spline wavelets
90.92
ISO 16610-30:2015
Geometrical product specifications (GPS) — Filtration — Part 30: Robust profile filters: Basic concepts
60.60
ISO 16610-31:2016
Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters: Gaussian regression filters
60.60
ISO 16610-40:2015
Geometrical product specifications (GPS) — Filtration — Part 40: Morphological profile filters: Basic concepts
60.60
ISO 16610-41:2015
Geometrical product specifications (GPS) — Filtration — Part 41: Morphological profile filters: Disk and horizontal line-segment filters
60.60
ISO 16610-49:2015
Geometrical product specifications (GPS) — Filtration — Part 49: Morphological profile filters: Scale space techniques
60.60
ISO 16610-60:2015
Geometrical product specification (GPS) — Filtration — Part 60: Linear areal filters — Basic concepts
60.60
ISO 16610-61:2015
Geometrical product specification (GPS) — Filtration — Part 61: Linear areal filters — Gaussian filters
90.93
ISO 16610-61:2015/Amd 1
Geometrical product specification (GPS) — Filtration — Part 61: Linear areal filters — Gaussian filters — Amendment 1
60.00
ISO 16610-71:2014
Geometrical product specifications (GPS) — Filtration — Part 71: Robust areal filters: Gaussian regression filters
90.93
ISO 16610-85:2013
Geometrical product specifications (GPS) — Filtration — Part 85: Morphological areal filters: Segmentation
90.93
ISO/CD 16610-45
Geometrical product specifications (GPS) — Filtration — Part 45: Part 45: Profile Morphological: Segmentation
30.20
ISO/FDIS 16610-29
Geometrical product specifications (GPS) — Filtration — Part 29: Linear profile filters: wavelets
50.00
ISO/TS 16610-1:2006
Geometrical product specifications (GPS) — Filtration — Part 1: Overview and basic concepts
95.99
ISO/TS 16610-20:2006
Geometrical product specifications (GPS) — Filtration — Part 20: Linear profile filters: Basic concepts
95.99
ISO/TS 16610-22:2006
Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters: Spline filters
95.99
ISO/TS 16610-28:2010
Geometrical product specifications (GPS) — Filtration — Part 28: Profile filters: End effects
95.99
ISO/TS 16610-29:2006
Geometrical product specifications (GPS) — Filtration — Part 29: Linear profile filters: Spline wavelets
95.99
ISO/TS 16610-30:2009
Geometrical product specifications (GPS) — Filtration — Part 30: Robust profile filters: Basic concepts
95.99
ISO/TS 16610-31:2010
Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters: Gaussian regression filters
95.99
ISO/TS 16610-32:2009
Geometrical product specifications (GPS) — Filtration — Part 32: Robust profile filters: Spline filters
90.93
ISO/TS 16610-40:2006
Geometrical product specifications (GPS) — Filtration — Part 40: Morphological profile filters: Basic concepts
95.99
ISO/TS 16610-41:2006
Geometrical product specifications (GPS) — Filtration — Part 41: Morphological profile filters: Disk and horizontal line-segment filters
95.99
ISO/TS 16610-49:2006
Geometrical product specifications (GPS) — Filtration — Part 49: Morphological profile filters: Scale space techniques
95.99
ISO 17450-1:2011
Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
90.93
ISO 17450-2:2012
Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators, uncertainties and ambiguities
90.93
ISO 17450-3:2016
Geometrical product specifications (GPS) — General concepts — Part 3: Toleranced features
60.60
ISO 17450-4:2017
Geometrical product specifications (GPS) — Basic concepts — Part 4: Geometrical characteristics for quantifying GPS deviations
60.60
ISO/TS 17450-1:2005
Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
95.99
ISO/TS 17450-1:2005/Cor 1:2007
Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification — Technical Corrigendum 1
95.99
ISO/TS 17450-2:2002
Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators and uncertainties
95.99
ISO/TS 17450-2:2002/Cor 1:2004
Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators and uncertainties — Technical Corrigendum 1
95.99
ISO/TS 17863:2013
Geometrical product specification (GPS) — Tolerancing of moveable assemblies
90.20
ISO/TS 17865:2016
Geometrical product specifications (GPS) — Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty for CMMs using single and multiple stylus contacting probing systems
90.20
ISO 18391:2016
Geometrical product specifications (GPS) — Population specification
60.60
ISO 20170:2019
Geometrical product specifications (GPS) — Decomposition of geometrical characteristics for manufacturing control
60.60
ISO/FDIS 21204
Geometrical product specifications (GPS) — Transition specification
50.00
ISO/TS 21619:2018
Geometrical product specifications (GPS) — Types of documents with GPS
60.60
ISO/CD 21920-1
Geometrical product specifications (GPS) — Surface texture: Profile — Part 1: Indication of surface texture
30.99
ISO/CD 21920-2
Geometrical product specifications (GPS) — Surface texture: Profile — Part 2: Terms, definitions and surface texture parameters
30.99
ISO/CD 21920-3
Geometrical product specifications (GPS) — Surface texture: Profile — Part 3: Specification operators
30.99
ISO/DIS 22081
Geometrical product specifications (GPS) — Geometrical tolerancing — General geometrical specifications and general size specifications
40.99
ISO 22432:2011
Geometrical product specifications (GPS) — Features utilized in specification and verification
90.93
ISO/TS 23165:2006
Geometrical product specifications (GPS) — Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty
90.20
ISO/DTR 23276
Program flowchart for feature parameters
30.60
ISO/TR 23605:2009
Technical product specification (TPS) — Application guidance — International model for national implementation
95.99
ISO/TR 23605:2018
Technical product specification (TPS) — Application guidance — International model for national implementation
60.60
ISO/NP TR 23850
Geometrical Product Specification (GPS) — Association — Mathematical concepts
10.99
ISO 25178-1:2016
Geometrical product specifications (GPS) — Surface texture: Areal — Part 1: Indication of surface texture
60.60
ISO 25178-2:2012
Geometrical product specifications (GPS) — Surface texture: Areal — Part 2: Terms, definitions and surface texture parameters
90.92
ISO 25178-3:2012
Geometrical product specifications (GPS) — Surface texture: Areal — Part 3: Specification operators
90.93
ISO 25178-600:2019
Geometrical product specifications (GPS) — Surface texture: Areal — Part 600: Metrological characteristics for areal topography measuring methods
60.60
ISO 25178-601:2010
Geometrical product specifications (GPS) — Surface texture: Areal — Part 601: Nominal characteristics of contact (stylus) instruments
90.93
ISO 25178-602:2010
Geometrical product specifications (GPS) — Surface texture: Areal — Part 602: Nominal characteristics of non-contact (confocal chromatic probe) instruments
90.93
ISO 25178-603:2013
Geometrical product specifications (GPS) — Surface texture: Areal — Part 603: Nominal characteristics of non-contact (phase-shifting interferometric microscopy) instruments
90.93
ISO 25178-604:2013
Geometrical product specifications (GPS) — Surface texture: Areal — Part 604: Nominal characteristics of non-contact (coherence scanning interferometry) instruments
90.93
ISO 25178-605:2014
Geometrical product specifications (GPS) — Surface texture: Areal — Part 605: Nominal characteristics of non-contact (point autofocus probe) instruments
90.93
ISO 25178-606:2015
Geometrical product specification (GPS) — Surface texture: Areal — Part 606: Nominal characteristics of non-contact (focus variation) instruments
90.92
ISO 25178-607:2019
Geometrical product specifications (GPS) — Surface texture: Areal — Part 607: Nominal characteristics of non-contact (confocal microscopy) instruments
60.60
ISO 25178-6:2010
Geometrical product specifications (GPS) — Surface texture: Areal — Part 6: Classification of methods for measuring surface texture
90.93
ISO 25178-701:2010
Geometrical product specifications (GPS) — Surface texture: Areal — Part 701: Calibration and measurement standards for contact (stylus) instruments
90.93
ISO 25178-70:2014
Geometrical product specification (GPS) — Surface texture: Areal — Part 70: Material measures
90.93
ISO 25178-71:2012
Geometrical product specifications (GPS) — Surface texture: Areal — Part 71: Software measurement standards
95.99
ISO 25178-71:2017
Geometrical product specifications (GPS) — Surface texture: Areal — Part 71: Software measurement standards
60.60
ISO 25178-72:2017
Geometrical product specifications (GPS) — Surface texture: Areal — Part 72: XML file format x3p
60.60
ISO 25178-72:2017/DAmd 1
Geometrical product specifications (GPS) — Surface texture: Areal — Part 72: XML file format x3p — Amendment 1
40.99
ISO 25178-73:2019
Geometrical product specifications (GPS) — Surface texture: Areal — Part 73: Terms and definitions for surface defects on material measures
60.60
ISO/CD 25178-700
Geometrical product specifications (GPS) — Surface texture: Areal — Part 700: Calibration, adjustment and verification of areal topography measuring instruments
30.20
ISO/CD 25178-72
Geometrical product specifications (GPS) — Surface texture: Areal — Part 72: XML file format x3p
30.98
ISO/DIS 25178-2
Geometrical product specifications (GPS) — Surface texture: Areal — Part 2: Terms, definitions and surface texture parameters
40.00
ISO 25378:2011
Geometrical product specifications (GPS) — Characteristics and conditions — Definitions
90.93

По запросу ничего не найдено. Пожалуйста, попробуйте изменить настройки фильтра.