Pipeline flanges for general use — Metric series — Mating dimensions

Pipeline flanges for general use — Shapes and dimensions of pressure-tight surfaces

Unplasticized polyvinyl chloride (PVC) pressure pipes and fittings, metric series — Dimensions of flanges

Metal pipes and fittings — Stainless steel bends and tees for the food industry

Metal pipes and fittings — Stainless steel clamp liners with gaskets for the food industry

Metal pipes and fittings — Stainless steel screwed couplings for the food industry

Assembled joints between fittings and polyethylene (PE) pressure pipes — Test of leakproofness under internal pressure

Plastics piping systems — Mechanical joints between fittings and pressure pipes — Test method for leaktightness under internal pressure

Polyethylene (PE) pressure pipes — Joints assembled with mechanical fittings — Internal under-pressure test method and requirement

Plastic piping systems — Mechanical joints between fittings and pressure pipes — Test method for leaktightness under negative pressure

Unplasticized polyvinyl chloride (PVC) pressures pipes — Metric series — Dimensions of adapter for backing flange

Assembled joints between fittings and polyethylene (PE) pressure pipes — Test of resistance to pull out

Plastics piping systems — Mechanical joints between fittings and pressure pipes — Test method for resistance to pull-out under constant longitudinal force

Assembled joints between fittings and polyethylene (PE) pressure pipes — Test of leakproofness under internal pressure when subjected to bending

Plastics piping systems — Mechanical joints between fittings and pressure pipes — Test method for leaktightness under internal pressure of assemblies subjected to bending

Polyethylene (PE) pressure pipes and fittings, metric series — Dimensions of flanges

Metallic flanges — Part 1: Steel flanges

Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems

Metallic flanges — Part 2: Cast iron flanges

Metallic flanges — Part 3: Copper alloy and composite flanges

Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness of flexible joints

Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness and proof of structural design of flexible joints

Thermoplastics pipes for fluids under pressure — Mating dimensions of flange adapters and loose backing flanges

Thermoplastics piping systems for fluids under pressure — Flange adapters and loose backing flanges — Mating dimensions

Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion

Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion

Plastics piping systems — Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints — Test method for leaktightness and strength while subjected to bending and internal pressure

Plastics piping systems — End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping — Test method for long-term leaktightness under internal water pressure

Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint

Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint — Amendment 1

Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm — Amendment 1: Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies

Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies — Amendment 1: Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies

Plastics pipes and fittings — Decohesion test of polyethylene (PE) saddle fusion joints — Evaluation of ductility of fusion joint interface by tear test

Metallic tube connections for fluid power and general use — Test methods for hydraulic fluid power connections

Metallic tube connections for fluid power and general use — Test methods for hydraulic fluid power connections — Technical Corrigendum 1

Metallic tube connections for fluid power and general use — Test methods for hydraulic fluid power connections

Metallic tube connections for fluid power and general use — Test methods for hydraulic fluid power connections

Plastics piping systems — Thermoplastics pipes and fittings for hot and cold water — Test method for the resistance of joints to pressure cycling

Plastics pipes and fittings — Format of a technical file for characterizing PE spigot end fittings

Petroleum and natural gas industries — Compact flanged connections with IX seal ring

Petroleum and natural gas industries — Compact flanged connections with IX seal ring — Technical Corrigendum 1

Petroleum and natural gas industries — Compact flanged connections with IX seal ring